SHOW ME TELL
ME TEST QUESTIONS
Example one
1. Show me how you would check that the direction indicators are working.
Applying the
indicators or hazard warning switch and check functioning of all indicators.
(may need to switch ignition on, prompt not to start engine)
2. Tell me how you would check that the brakes are
working before starting a journey.
Brakes should not feel spongy or slack. Brakes should be tested as you set off.
Vehicle should not pull to one side.
Example two
1. Identify where the windscreen washer reservoir is and tell me how you would
check the windscreen washer level.
Identify
reservoir and explain how to check level.
2. Show me how you would check
that the brake lights are working on this car. (I can assist you, if you need to
switch the ignition on, please don't start the engine)
Operate brake pedal,
make use of reflections in windows, garage doors, etc, or ask someone to help.
(may need to switch ignition on, prompt not to
start engine)
Example three
1. Show me / explain how you would check that the power assisted steering is
working before starting a journey.
If the steering
becomes heavy the system may not be working properly. Before starting a journey
two simple checks can be made. Gentle pressure on the steering wheel, maintained
while the engine is started, should result in a slight but noticeable movement
as the system begins to operate. Alternatively turning the steering wheel just
after moving off will give an immediate indication that the power assistance is
functioning.
2. Tell me where you would find
the information for the recommended tyre pressures for this car and how tyre
pressures should be checked.
Manufacturer’s guide, use a
reliable pressure gauge, check and adjust pressures when tyres are
cold, don’t forget spare tyre, remember to refit valve caps.
Example four
1.
Show me how you
would check the parking brake (handbrake) for excessive wear, make sure you keep
safe control of the vehicle.
Apply footbrake firmly.
Demonstrate by applying parking brake (handbrake) so that when it is fully
applied it secures itself, and is not at the end of the working travel.
2. Identify where the
windscreen washer reservoir is and tell me how you would check the windscreen
washer level.
Identify reservoir and explain how
to check level.
Example five
1. Open the bonnet, identify where you would check the
engine oil level and tell me how you would check that the engine has sufficient
oil.
Identify
dipstick / oil level indicator, describe check of oil level against the
minimum/maximum markers.
2. Tell me where you
would find the information for the recommended tyre pressures for this car and
how tyre pressures should be checked.
Manufacturer’s guide, use a reliable
pressure gauge, check and adjust pressures when tyres are cold, don’t forget
spare tyre, remember to refit valve caps.
Example six
1. Open the bonnet, identify where you would check the
engine coolant level and tell me how you would check that the engine has the
correct level.
Identify
high/low level markings on header tank where fitted or radiator filler cap, and
describe how to top up to correct level.
2. Tell me how you make sure your head restraint is correctly adjusted so it
provides the best protection in the event of a crash.
The head restraint should be
adjusted so the rigid part of the head restraint is at least as high as the eye
or top of the ears,
and as close to the back of the head as is comfortable. N.B. Some restraints
might not be adjustable
Example seven
1. Open the bonnet, identify where the brake fluid
reservoir is and tell me how you would check that you have a safe level of
hydraulic brake fluid.
Identify
reservoir, check level against high/low markings.
2. Tell me how you would check the tyres to ensure that they have sufficient
tread depth and that their general condition is safe to use on the road.
No cuts and bulges, 1.6mm of tread
depth across the central ¾ of the breadth of the tyre and around the entire
outer circumference.
Example eight
1. Show me how you would check that the horn is
working (off road only).
Check is
carried out by using control (turn on ignition if necessary).
2. Tell me how you would check the tyres to ensure that they have sufficient
tread depth and that their general condition is safe to use on the road.
No cuts and bulges, 1.6mm of tread
depth across the central ¾ of the breadth of the tyre and around the entire
outer circumference.
Example nine
1. Tell me how you would check that the brakes are
working before starting a journey.
Brakes should
not feel spongy or slack. Brakes should be tested as you set off. Vehicle should
not pull to one side.
2.
Show me how you would clean the windscreen using the windscreen washer and
wipers.
Operate control to wash and wipe
windscreen (turn ignition on if necessary).
Example ten
1. Tell me how you would check that the headlights &
tail lights are working. (No need to exit vehicle)
Explanation: Operate switch
(turn on ignition if necessary), then walk round vehicle. (As this is a "Tell
Me" question, there is no need to physically check the lights.)
2. Show me how you would set the demister controls to clear all the windows
effectively, this should include both front and rear screens
Set all relevant controls including; fan,
temperature, air direction / source and heated screen to clear windscreen and
windows. Engine does not have to
be started for this demonstration.
Example eleven
1. Show me how you would switch on the rear fog light(s) and explain when
you would use it/them. (No need to exit vehicle)
Operate switch (turn on
dipped headlights and ignition if necessary). Check warning light is on. Explain
use.
2. Tell me how you would know if there was a problem with your anti lock braking
system.
Warning light should
illuminate if there is a fault with the anti lock braking system.
Example twelve
1. Show me how you would check that the brake lights
are working on this car. (I can assist you, if you need to switch the ignition
on, please don't start the engine)
Operate brake
pedal, make use of reflections in windows, garage doors, etc, or ask someone to
help. (may need to switch ignition on, prompt not to start engine)
2. Tell me how you would check that the headlights & tail lights are working.
(No need to exit vehicle)
Explanation: Operate switch (turn on
ignition if necessary), then walk round vehicle. (As this is a "Tell Me"
question, there is no need to physically check the lights.)
Example Thirteen
1. Show me how you switch your headlight from dipped to main beam and
explain how you would know the main beam is on whilst inside the car.
Operate switch (with
ignition or engine on if necessary), check with main beam warning light.
2. Tell me how you would know if there was a problem with your anti lock braking
system.
Warning light should illuminate if
there is a fault with the anti lock braking system.
|